Site Loader

If your replacement hard drive does not have the hard drive bracket attached, remove the bracket from the old drive by unsnapping it from the drive. Use care when handling the front-panel release tabs to avoid damaging them. To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module. For additional information on the type of memory supported by your computer, see your Owner’s Manual. You can do so by touching an unpainted metal surface on the computer chassis. Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer.

Uploader: Arashinris
Date Added: 13 October 2016
File Size: 9.78 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 91859
Price: Free* [*Free Regsitration Required]

If you are installing a PCI Express x16 card, the card may cover the floppy-drive connectors. Snap the bracket onto the new drive.

To continue using , please upgrade your browser.

You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when f510 turn on the computer. Otherwise, your computer may not start properly. Ensure that the tab on the processor cover is positioned underneath the release lever at the front of the socket.

You can do so by touching an unpainted metal surface on the computer chassis.

You must route these cables properly when you replace them to prevent them from being pinched or crimped. If the card is not removed correctly, the system board may be damaged. Leave the release lever extended lci the release position so that the socket is ready for the new processor.

  MICRO INNOVATIONS IC320 DRIVER

If you are installing a processor upgrade kit from Dell, discard the original heat-sink assembly. If the DDR2 memory modules are not installed in matched pairs, the computer will continue to operate, but with a slight reduction in performance.

Dell Dimension

When removing an IDE drive data cable, grasp the colored pull-tab and pull until the connector detaches. Do not set the heat-sink assembly upright or touch the thermal interface, as this may result in damage to the thermal interface material. The sliding plate secures and releases the drive panel and helps to secure the drives.

If you are not installing a processor pic kit from Dell, reuse the original heat-sink assembly when you install your new processor. If you insert the module correctly, the securing clips snap into the cutouts at each end of the module. If you installed a processor replacement kit from Dell, return the original heat-sink assembly and processor to Dell in the same package in which your replacement kit was sent.

Despite having a plastic shield, the heat-sink assembly may be very hot during normal operation. Your computer supports DDR2 memory.

Certain components within the computer require address space in the 4-GB range. E150 additional information on the type of memory supported by your computer, see your Owner’s Manual. If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell.

Ensure that the assembly has had sufficient time to cool f510 you touch it. To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer. Use the pull-tab to remove the data cable from your hard drive or from the system board.

  ASUS EXTREME AX600 PRO DRIVER DOWNLOAD

When you install a filler bracket, ensure that the bracket is seated correctly. If you are installing or replacing a PCI Express card, follow the procedures in the next section.

See the documentation that came with the drive for instructions e5100 installing any software required for drive operation. Use care d510 handling the front-panel release tabs to avoid damaging them. Do not route card cables over or behind the cards.

When removing or replacing the processor, do not touch any of the pins inside the processor socket or allow any objects to fall onto the pins in the socket. Remove the card before connecting the floppy-drive cables. Instead, set the drive on a surface, such as a foam pad, that will sufficiently cushion it. See the label on the module to determine the module’s capacity.

If you are installing or replacing w510 card, follow the procedures in the next section. Grasp the card by its top corners, and ease it out of its connector. If you are installing a new drive, you need to remove the drive-panel insert.